Espalier Kit – Diamond King

[vc_row][vc_column][vc_column_text]

[/vc_column_text][/vc_column][/vc_row][vc_row text_align=”center” padding_top=”0″ padding_bottom=”30″ oblique_section=”no” oblique_section_top_and_bottom=”both” oblique_section_position=”from_left_to_right” triangle_shape=”no” triangle_shape_position=”both”][vc_column][vc_column_text]

Starter kit for a king diamond espalier installation

[/vc_column_text][vc_separator type=”transparent” up=”20″][vc_column_text]With this kit you will get all the components you require to install a diamond patterned espalier set-up as shown in the diagram below. (Wire not included) This creates a stylish pattern when growing with vines such as star jasmine, clematis or bougainvillea. Ideal to turn a wall or fence into a growing work of art. This system can be used for fixing onto timber fences, concrete block or brick substrates using screw plugs. Use either AWG 12 (2 mm) stainless steel wire rope or AWG 12 (2 mm) soft wire.[/vc_column_text][vc_separator type=”transparent” up=”40″][vc_single_image image=”51840″ img_size=”large” alignment=”center”][vc_separator type=”transparent” up=”20″][vc_column_text]

CAUTION : DO NOT FORCE WIRE THROUGH ANCHOR
Gently insert wire using back and forth motion until wire slides comfortably between the locking jaws.

[/vc_column_text][vc_empty_space][vc_column_text]

How to extend the Diamond Pattern King Kit

[/vc_column_text][vc_separator type=”transparent” up=”20″][vc_single_image image=”51692″ img_size=”large” alignment=”center”][vc_empty_space][/vc_column][/vc_row][vc_row padding_top=”30″ padding_bottom=”30″ oblique_section=”no” oblique_section_top_and_bottom=”both” oblique_section_position=”from_left_to_right” triangle_shape=”no” triangle_shape_position=”both”][vc_column][vc_separator][/vc_column][/vc_row][vc_row oblique_section=”no” oblique_section_top_and_bottom=”both” oblique_section_position=”from_left_to_right” triangle_shape=”no” triangle_shape_position=”both”][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51146″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

REQUIRE TOOLS

[/vc_column_text][vc_column_text]The only tools you will require to complete this job are a power drill with a hex driver bit, 1/8 in (3 mm) drill bit, pop rivet gun and quality wire cutters.[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51315″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

STEP 1

[/vc_column_text][vc_column_text]

Plan your job carefully – this set up uses 2 runs of wire. Measure and markout your mounting points – note that the distance between these points should be equal for both vertical and horizontal.

[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51318″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

STEP 2

[/vc_column_text][vc_column_text]Fix the anchor platforms in place at each corner ensuring that they are set at a 45° angle.[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51319″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

STEP 3

[/vc_column_text][vc_column_text]Fix the radial wire guides at the intermediate positions – the guide should be vertical and horizontal as shown in corresponding position on the diagram. Also ensure the guide is the correct way around – one end has a groove for the wire to follow.[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][/vc_row][vc_row oblique_section=”no” oblique_section_top_and_bottom=”both” oblique_section_position=”from_left_to_right” triangle_shape=”no” triangle_shape_position=”both”][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51320″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

STEP 4

[/vc_column_text][vc_column_text]For the first wire run – insert wire through anchor platform and into Espalar anchor to hold in place. Note caution above.[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51322″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

STEP 5

[/vc_column_text][vc_column_text]Uncoil wire an feed through radial wire guides to the end point following the numbers on the above diagram.[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51321″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

STEP 6

[/vc_column_text][vc_column_text]Fit Espalar anchor at end point then tension wire with pop rivet gun. Trim wire and fit caps at both ends.[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][vc_column width=”1/2″ offset=”vc_col-md-3 vc_col-xs-12″][vc_single_image image=”51323″ img_size=”full”][vc_separator type=”transparent” thickness=”1″ up=”16″ down=”0″][vc_column_text]

STEP 7

[/vc_column_text][vc_column_text]Follow the process for the other run to complete your diamond pattern installation.[/vc_column_text][vc_separator type=”transparent” thickness=”1″ up=”30″ down=”0″][/vc_column][/vc_row][vc_row type=”grid” text_align=”center” background_color=”#f5f5f5″ padding_top=”80″ padding_bottom=”80″][vc_column][vc_column_text]

Get this diamond espalier starter kit.

[/vc_column_text][vc_separator type=”transparent” up=”30″][vc_column_text el_class=”ctapara”]

This kit provides all the components required to install a diamond set-up as shown in the above diagram.

Wire is not included in this kit.

A regular fence panel 3m x 2m requires 18 m of wire.

We recommend Stainless Steel Wire Rope.

[/vc_column_text][vc_separator type=”transparent” up=”30″][no_button size=”large” icon_pack=”” text=”SHOP NOW” link=”https://www.espalar.com/shop” color=”#ffffff” hover_color=”#ffffff” background_color=”#ff710e” hover_background_color=”#ea680b” padding=”60″ border_radius=”4″][vc_separator type=”transparent” up=”20″][/vc_column][/vc_row][vc_row][vc_column][vc_column_text]

[/vc_column_text][/vc_column][/vc_row]